Analytical modeling of complex contact behavior between rock mass and lining structure

Based on the nondestructive test data of operating railway tunnels in China, this paper summarizes the basic characteristics of the complex contact behavior between the rock mass and lining structure. The contact modes are classified into dense contact, local non-contact, and loose contact. Subsequently, the corresponding mechanical model for each contact mode is developed according to its mechanical characteristics using the complex variable method. In the proposed mechanical model, a special algorithm is introduced to detect whether the local non-contact zone is re-contacted. Besides, a novel conformal mapping method is also proposed to accurately calculate the mechanical response of the concrete lining. Finally, the accuracy of the proposed method is verified by comparing it with the finite element method (FEM). Several parameter investigations are conducted to analyze the effects of different contact modes on the rock–lining interaction. The results show that: (i) the height of the local non-contact area does not have a significant effect on the contact stress distribution if no re-contact occurs; (ii) backfill grouting can reduce the local stress concentration caused by poor contact modes; and (iii) reducing the friction coefficient of the interface can lead to a more uniform distribution of internal forces in the concrete lining.     

UV-enhanced conductive and dielectric properties in KTN crystal

We observe enhancements of both conductive and dielectric properties under UV illumination by using a ferroelectric absorber, potassium tantalate niobate (KTa_1-xNb_xO₃, KTN). The UV-generated electron-hole pairs weaken the intrinsic ferroelectric polarization while enhance the conductive property. The UV-induced heat effect causes the enhancement of the dielectric property. The results are further confirmed by the maximal rectification ratio which shows an opposite trend between the direct heating process and the UV illumination. Our results are useful for better understanding of ferroelectric properties under UV illumination and the development of new optoelectronic devices.     

Sustainable phenolic thermosets coatings derived from urushiol

The over-exploitation of finite fossil resources and/or the increased environmental and sustainable awareness inspire scientists and technologists to search for inexpensive alternatives from renewable chemicals. Phenol formaldehyde (PF) resins, the oldest type of synthetic polymers with good mechanical properties and heat resistance, are widely used in the production of coatings, laminates, molding compositions, and glues. Here, biobased urushiol-derived PF resins were synthesized from the alkali-catalyzed reaction between urushiol and formaldehyde. The chemical compositions and molecular structures of resole resins were characterized by carbon-13 nuclear magnetic resonance and Fourier transform infrared spectroscopy, and their curing behaviors were studied by differential scanning calorimetry. The as-prepared urushiol-derived resole resins had methylol (Ph−CH₂OH), ortho- and para-hemiformal groups (Ph−CH₂OCH₂OH), and the para−para/ortho−para/ortho−ortho links of methylene groups (Ph−CH₂−Ph), whereas the resole resins had low curing temperatures at about 100–113°C. Additionally, given the long side alkyl group moiety on the aromatic rings of urushiol, the films of cured urushiol-derived resole resins had low glass transition temperatures of 132 ± 2°C. Furthermore, the as-prepared urushiol-derived coatings exhibited excellent physical and mechanical properties.     

Manipulation of thick-walled PEEK bushing crystallinity and modulus via instrumented compression molding

An instrumented hot compression molding apparatus was fabricated to allow real-time monitoring and precise temperature control during the compaction and consolidation of large polyether ether ketone (PEEK) products. The objective was to determine the impact of controlled variables on the properties of the molded article. Four different strategies were designed to control the mold thermal profiles. The average crystallinity in a commercial molding process is restricted due to large thermal masses with low thermal conductivity. In contrast, this research was able to reduce the crystallinity range from 33% to 6% by developing a special controlled apparatus and implementing new processing methodologies. In this study, PEEK showed a significant increase in the modulus compared to typical values measured on commercially produced analogs, and a higher degree of property uniformity. In a single commercially molded PEEK billet, compressive modulus variability was 13% at room temperature, and 21% at 225°C. Properties of billets produced using the laboratory apparatus showed a reduction in variability to 2%.     

Interfacial interactions and properties of cellular structured polyurethane nanocomposite based on carbonaceous nano-fillers

In this article, we have studied the effect of carbonaceous nanofillers viz. fullerenol (0D), carboxylated multi-wall carbon nanotube (MWCNT, 1D), hydroxylated graphene (2D) and combination of carboxylated CNT and hydroxylated graphene as 3D in thermoplastic polyurethane on the tensile properties of the fabricated cellular structures. The concentration of nano-fillers was varied as 0.1, 1, and 5 wt%. Tensile properties of the nanocomposite cellular structures were measured as per ASTM D882 at 20°C (below glass transition temperature, T_g) and 40°C (above T_g). The results have shown that the tensile strength was found to increase by 200%–300% and the tensile modulus was found to increase by 150%–300% for 2D and 3D nano-fillers while significantly poor results were observed for 0D. However, the test data tensile strength and modulus showed marginal increase at 20°C and marginally low at 40°C for 1D filler. The interfacial adhesion was calculated by using experimental tensile data and the predictive models. The interfacial adhesion parameter (B_σ) calculated using Pukanszky equation was found significantly higher value for 2D (B_σ20 = 195.8) and 3D (B_σ20 = 192.0) fillers while poor adhesion was observed for 0D (B_σ20 = −81.6) fillers. The developed cellular structured materials were also evaluated by attenuated total reflection Fourier transform IR spectra, differential scanning calorimetry, X-ray diffraction, scanning electron microscope, and transmission electron microscope.     

改性聚乳酸发泡技术研究进展

综述了近几年国内外改性聚乳酸（PLA）发泡技术的研究进展，针对PLA在发泡方面熔体强度和结晶性能的不足，介绍了通过加入扩链剂、交联剂、成核剂、纤维和其他聚合物等物质来改善PLA发泡性能的方法、效果和机理；最后，对改性聚乳酸发泡技术的未来发展进行了展望。     

Investigation of the changes in physical properties of PES/PVC fabrics after aging

The aim of this work was to investigate the physical and mechanical performance of architectural polyester (PES)–poly(vinyl chloride) (PVC) membranes exposed to different artificial aging conditions. Two commercially available architectural membranes were chosen as research objects. The durability of the PES/PVC fabrics was evaluated by the loss in mechanical performance, scanning electron microscopy, and X-ray diffraction analysis in order to understand the effect of the degradation agents on the surface of the membranes. The mechanical performance of the PES/PVC membranes was unchanged. Scanning electron microscopy images of the tested materials showed initial cracks after aging. The X-ray fluorescence analysis showed that at the time of aging, the amount of Cl and Si decreased slightly, while Ti decreased by half, and Ca by volume increased twice. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47523.